Quick release mounting bracket for the extension pole used on the ATSL generator lights. Use the scene lights on the truck then pull them off to use on the ATSL frame.
Traffic Safety System is proud to be a dealer for Fire Research Corp products.If you don't find the products you are looking for please contact us. We will meet or beat the price on any comperable item.
(828) 275-6954
Scene light, portable generator, Honda generator, fire research, fire pump, arrow board, scene lighting, traffic safety system, police lights, emergency warning light
You are here: Home > TSS Scene Lights > Fire Research Corp > Governors, throttles and guages
Product Details:
Flow Sensor and Mounts General
Standard Features 
A saddle clamp is the standard mounting for 2" through 6" pipe sizes. (Some larger sizes are available). Drill and deburr a 1¾" hole for the sensor and clamp this fitting down over the hole. A thick rubber gasket prevents leaks. The sensor housing is epoxied in place at the factory and is notched so the sensor inserts in the correct orientation. Not a victaulic clamp, our clamps use a simple "U-bolt" type fitting. Pictured with brass sensors housing, brass retaining cap, and sensor. 
Weldment fittings can be installed in the pipe when you do not have enough room for a saddle clamp. It is available in aluminum, steel and stainless steel. Enduser must ensure that the sensor housing is orientated with the flow, as the parts are not supplied epoxied. A True-Seal locknut is provided to hold the sensor housing in place and prevent leaks. Standard sizes range from 2.0" through 6". Pictured with the brass sensor housing, True-Seal locknut (to prevent leaks), brass retaining cap, and sensor. 
Pipe Tee fittings are NPT threaded, " for applications where standard pipe fittings are the easiest solution. The sensor housing is epoxied in place at the factory and is notched so the sensor inserts in the correct orientation. Standard sizes range range from 1.5" through 4. Pictured with brass sensor housing, brass retaining cap, and sensor. 
Third party spacer adapters are available for side discharge applications where a spacer is the only thing that will fit. Enduser must ensure that the sensor housing is orientated with the flow, as the parts are not supplied epoxied. Custom adapters require a print with all dimensions and bolt patterns. The brass sensor housing may be fit with an O-ring for certain third-party spacers or adapters.
- No magnets in the paddlewheel rotor.
- Completely sealed electronics.
- Multiple mounting options.
- Can be used on large diameter pipes
- Body Material - Acetal (Delrin)
- Rotor - 6-bladed
- Rotor Shaft - Stainless Steel (316)
- Excitation Voltage - 5 volts DC
- Output Frequency - 3 to 150 Hz
- Maximum Pressure - 600 PSI
Flow causes the paddlewheel to rotate on a stainless steel pin. The sensor is resistant to damage from debris in the water because the paddle is free spinning and moves with the flow. The paddlewheel revolutions are converted into electrical signals and the flow sensor provides an output signal with a frequency proportional to the flow rate.
MOUNTING OPTIONS
Saddle Clamp
A saddle clamp is the standard mounting for 2" through 6" pipe sizes. (Some larger sizes are available). Drill and deburr a 1¾" hole for the sensor and clamp this fitting down over the hole. A thick rubber gasket prevents leaks. The sensor housing is epoxied in place at the factory and is notched so the sensor inserts in the correct orientation. Not a victaulic clamp, our clamps use a simple "U-bolt" type fitting. Pictured with brass sensors housing, brass retaining cap, and sensor. Weldment
Weldment fittings can be installed in the pipe when you do not have enough room for a saddle clamp. It is available in aluminum, steel and stainless steel. Enduser must ensure that the sensor housing is orientated with the flow, as the parts are not supplied epoxied. A True-Seal locknut is provided to hold the sensor housing in place and prevent leaks. Standard sizes range from 2.0" through 6". Pictured with the brass sensor housing, True-Seal locknut (to prevent leaks), brass retaining cap, and sensor. Pipe Tee
Pipe Tee fittings are NPT threaded, " for applications where standard pipe fittings are the easiest solution. The sensor housing is epoxied in place at the factory and is notched so the sensor inserts in the correct orientation. Standard sizes range range from 1.5" through 4. Pictured with brass sensor housing, brass retaining cap, and sensor. Third Party Spacer Adapters
Third party spacer adapters are available for side discharge applications where a spacer is the only thing that will fit. Enduser must ensure that the sensor housing is orientated with the flow, as the parts are not supplied epoxied. Custom adapters require a print with all dimensions and bolt patterns. The brass sensor housing may be fit with an O-ring for certain third-party spacers or adapters. Traffic Safety System, L.L.C.
116 Carriage Drive, Fairview, North Carolina 28730
(828) 275 6954
116 Carriage Drive, Fairview, North Carolina 28730
(828) 275 6954
